Data Sheets for AeroLEDs Products are here.
AeroLEDs™ LIMITED WARRANTY AND LIMITATION OF LIABILITY
AeroLEDs™ warrants that on the Date of Purchase this Product will conform to AeroLEDs™ published specifications for the product, which are available from AeroLEDs™ on request, and AeroLEDs™ warrants that the product is free from defects in materials and workmanship. This Limited Warranty extends for five (5) years from the date of purchase or from when an air worthiness certificate is issued.
This Limited Warranty does not apply to parts or products that are misused; abused; modified; damaged by accident, fire or other hazard; improperly installed or operated; or not maintained in accordance with the maintenance procedures set forth in AeroLEDs™ Installation and Operating Instructions. To obtain warranty service you must complete the warranty card that is included with your product and return within 14 days to 8475 W. Elisa Street, Boise, Idaho 83709. If you did not receive a warranty card please contact customer service at 208 850-3294 or fax a request to 208 246-0552.
EXCLUSION OF OTHER WARRANTIES: AeroLEDs™ MAKES NO OTHER WARRANTIES, EXPRESS,
IMPLIED OR STATUTORY. THE IMPLIED WARRANTIES FOR MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT.
BUYERS SOLE AND EXCLUSIVE REMEDY IN CONTRACT, TORT OR UNDER ANY OTHER THEORY
AGAINST AeroLEDs™ RESPECTING THE PRODUCT AND ITS USE SHALL BE THE REPLACEMENT
OR REPAIR OF THE PRODUCT AS DESCRIBED ABOVE. LIMITATION OF LIABILITY: IN THE EVENT
OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM
RELATED TO AeroLEDs™ PRODUCTS, AeroLEDs™ LIABILITY FOR DAMAGES SHALL BE LIMITED
TO THE AMOUNT PAID FOR THE PRODUCT AT THE TIME OF ORIGINAL PURCHASE. IN NO EVENT
SHALL AeroLEDs™ BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR
LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES
BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, NEGLIGENCE OR OTHER CLAIM, EVEN
IF AeroLEDs™ OR A AeroLEDs™ REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF
AeroLEDs™ shall have no further obligation or liability with respect to the product or its sale, operation and use, and AeroLEDs™ neither assumes nor authorizes the assumption of any other obligation or liability in connection with such product.
This Limited Warranty gives you specific legal rights, and you may also have other legal rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental consequential damages, so the above exclusion or limitation may not apply to you.
Any oral statements or representations about the product which may have been made by salesmen or AeroLEDs™ representatives do not constitute warranties. This Limited Warranty may not be amended, modified or enlarged, except by a written agreement signed by an authorized official of AeroLEDs™ which expressly refers to this Limited Warranty.
What is the difference between the Pulsar NS and the Pulsar NSP?
The Pulsar NS has a forward red or green navigation light, and a strobe that covers 180 degrees from each wing tip.
The Pulsar NSP has a forward red or green navigation light, a strobe that covers 180 degrees from each wing tip, and a rear white position light.
What are the installation requirements for the Sunspot 36?
The Sunspot 36LX landing and taxi lights can be installed with just a log book entry if you can install the light in an existing mount and use the existing wires, switches, and circuit breakers.
The Sunspot 36HX landing and taxi lights can be installed with the pulse function enabled in a Cessna 185 under STC, or in other aircraft models with a 337 that uses the Cessna 185 STC as a basis for approval.
What are the installation requirement for the TSO Lights?
If the lights are mounted to an existing mounting location with no structural modifications, and existing wiring can be re-used, the lights can be installed with a log book entry.
If there are modifications to the wiring, a 337 should be submitted for approval for the installation.
If there are structural modifications made to mount the lights, a more extensive approval may be required, ranging from a 337 to an STC.
What are the recommended wire for the Pulsar and Suntail lights?
We recommend 3 conductor 20 gauge shielded single bundle wire, which we have available in our accessories area.